Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
On this page below you will find a bunch of really good data involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't specifically brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and embeded in the brand-new one. Make sure you have qualified yourself for the job as well as are comfortable trying it. As opposed to employing a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will help you mount a brand-new bath tub in your shower room if you have actually already bought a new bathtub and also do not need to change the arrangement of your previous water pipelines.
Your tools and material checklist need to consist of the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and check all joints and new pipework for leaks as well as tighten them if needed. Fill up the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealer can crack rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Post feedback down below. We'd be delighted to know your insights about this write up. We are looking forward that you come back again later on. Remember to take the opportunity to promote this content if you enjoyed reading it. Thank you for your time spent reading it.
Find Out More Report this page